Usage

The transfer ladle preheating device is also called a preheater. It is mainly used to quickly and uniformly increase the temperature of the molten alumnium ladle lining to reduce heat loss during molten alumnium pouring and prolong the service life of the molten alumnium ladle lining. Heating energy source can be gas or electricity.

Gas Heating Molten Aluminum Transfer Ladle Preheating Equipment uses natural gas as fuel and is mainly used for rapid heating of ladle in the process of transferring molten aluminum. It can also be used to heat new ladle and cold repair ladle. Through our company's many years of experience accumulation, perfection and continuous improvement, the product function and quality have been developed by leaps and bounds. It is a new generation of high-efficiency gas preheater independently developed by our company.

Equipment Features
• Natural gas (NG) or LPG can be chosen as the fuel.
• The heating speed can be adjusted within a wide range.
• Fully combusted, energy-saving and environment-friendly.
• Gas and combustion air pressure detection, abnormal ignition alarm.
• Heating temperature and time are controllable.
• Long open flame ignition function.

• Flame detection function

Equipment Advantage

◇The preheating device adopts natural gas burner, with high flame ejection speed, long flame, good rigidity, direct injection to the bottom of the ladle, uniform heating temperature of the ladle lining, and fast heating speed.

◇The equipment is safe and reliable. Set up a variety of emergency stop controls to ensure that the system can be stopped and alarmed in any fault state, effectively ensuring the safety of personnel and equipment.

◇The setting of heating control has two modes, which can be adjusted freely according to the requirements of on-site use. Mode 1: The heating time can be preset within the range of 0-60min, and the heating will be automatically stopped when the preset time is reached, and the sound and light will prompt. Mode 2: Do not limit the heating time, stop heating manually. It can automatically detect flameout and alarm, and cut off the fuel supply.

◇The heating speed is fast and the temperature in the ladle is even. The heating rate can be adjusted from 0-20℃/min to ensure that the ladle can rise from room temperature to the normal operating temperature of about 550℃ within 30 minutes. The heating flame of the ladle can cover the entire cavity of the ladle to ensure that the maximum temperature difference at each point in the ladle is ≤50℃.

◇The operation is simple and convenient. The preheating cover can be driven by a cylinder to move up and down to facilitate the placement of the ladle.

◇Wide range of application. The heating cover is connected by a short ring chain, which is suitable for heating a variety of high aluminum ladle.

◇Low noise. Using low-noise and high-pressure combustion-supporting fan, the noise is not more than 80 dB.

Technical Parameter

• Maximum heating temperature: 1200℃

• Temperature uniformity: ±20℃

• Temperature control accuracy: ±10℃

• Heating power: 110-800kw

1. MAIN PARAMETERS

Equipment Pictures

Founded in January 2003,Jinan HYDEB Thermal Tech Co., Ltd. is located in Jinan High-tech Development Zone.

Hydeb mainly produces molten aluminum refining and degassing units, molten aluminum transfer ladles and holding crucible furnaces, which are sold to well-known corporations in the industry at home and abroad, meeting their high requirements for product safety and advancement.

Focusing on the aluminum casting industry, the Company takes “Technology, Quality and Service” as its base of enterprise, aimed at meeting all the needs of customers. Being “Safe, Practical, Reliable, Efficient and nice-looking”, its products are well unanimous recognized by the customers, with its brand “HYDEB” gaining high popularity in the industry.

To meet the increasingly high requirements for aluminum casting products, HYDEB gives full play to its technological superiority and engages industry experts as technical directors, developing products urgently needed in the market such as the counter (low) pressure casting holding crucible furnaces and molten aluminum refining and degassing units. It has also established long-term and friendly partnerships with a number of large-scale Chinese integrated equipment suppliers, sustaining its annual supply level of more than 80 sets.

“Taking the lead and creating a brand name in the industry”. We will continue to advance on the path of professional development and continually improve our products and services to further meet our customers’ development needs and support their creation of greater values.